The APM Power Module is a simple way of providing your APM with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable. The on-board switching regulator outputs 5.3V and a maximum of 2.25A from up to a 4S LiPo battery. The Power Module comes completely assembled with XT60 connectors, and wrapped in shrink tubing for protection.
The ArduPilot Mega 2.6 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition. This version is ready to use, with no assembly required. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints..
This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it's often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility in that positioning and is a good choice for them, too). This is designed to be used with the 3DR uBlox GPS with Compass (see option below), so that the GPS/Compass unit can be mounted further from noise sources than APM itself. .
APM 2.6 requires a GPS unit and external compass for full autonomy. Choose your compass from options menu at right.
The benefits of the Pixhawk system include integrated multithreading, a Unix/Linux-like programming environment, completely new autopilot functions such as sophisticated scripting of missions and flight behavior, and a custom PX4 driver layer ensuring tight timing across all processes.
The next evolution of the rotor revolution is here!! The KK2.1 is packing new found power with updated sensors, memory and header pins.
The KK2.1 is next big evolution of the first generation KK flight control boards. The KK2.1 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than ever. A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and you’re ready to go! All of which is done with easy to follow on screen prompts!
The original KK gyro system has been updated to an incredibly sensitive 6050 MPU system making this the most stable KK board ever and allowing for the addition of an auto-level function. At the heart of the KK2.1 is an Atmel Mega644PA 8-bit AVR RISC-based microcontroller with 64k of memory. An additional polarity protected header has been added for voltage detection, so no need for on-board soldering. A handy piezo buzzer is also included for audio warning when activating and deactivating the board.
The KK2.1 added polarity protection to the voltage sense header and a fuse protected buzzer outputs, in case something is accidentally plugged in incorrectly. The voltage sense line has been updated for better accuracy. The board is clearly labeled and the voltage sense line color has been changed to red for easy identification, making installation and connections a snap.
If you’re new to multi-rotor flight or have been unsure about how to setup a KK board then the KK2.1 was built for you. The 6 Pin USBasp AVR programming interface ensures future software updates will be quick and easy.
This Ublox GPS module uses an active circuitry ceramic patch antenna to provide excellent GPS signal which outperforms the older Ublox Neo 6 series modules. This Ublox Neo 7 module also includes a rechargeable backup battery to allow for HOT starts and also includes an i2c EEPROM to store the configuration settings. Out of the box this GPS module is configured to run at 38400 Baud and is configured to run with APM/Pixhawk systems. This GPS module includes two cables, a 6pin connector for the GPS module and a 4 pin connector for the i2c compass.
UBLOX NEO 7M Features:
2.4GHz is the standard of new generation radio system because it has a lot of advantages. Operating at 2.4 GHz puts the radio control out of the frequency range of any 'noise' generated by the other electronic components on your helicopter - such as the brushless motor, Electronic speed controller, Servos and any metal to metal noise - eliminating interference and glitching that can affect traditional frequency system.
FS TH9X 2.4GHz 9 Channel RC Helicopter/Plane Transmitter Specification
- channels: 9channels;
- model type:heli,airplane,glid;
- RF power:less than 20db;
- code type:PPM/PCM;
- lcd type:128*64 dot;
- low voltage warning:yes;
- DSC port:yes;
- charger port: yes;
- ANT length:26mm;
- Color: black;
- certificate: CE?FCC;
Description:- Do you have an R/C vehicle battery pack that desperately needs a Deans connector? With our new M/F Deans connector pair, you’ll have just what you need to safely and securely connect your battery or anything else that requires a mini T Plug.
Each pack comes with one male and one female Deans connector and each can support a current of, up to, 30A.